Easy Lighting For North State Bird Feeders

The doors on most of the other buildings are too large to look right with my trains. But in the winter, when I don't want to expose my model buildings to snow, sleet, and strong winds, I use several.

The North State bird feeders have one "feature" that makes them especially useful for harsh weather: broad bases that can hold gravel (instead of bird seed), weighting the buildings down against our harsh winter and early spring winds.

In times past, I have camouflaged the bases by burying them completely in gravel, as shown in the photo to the right.

Some years I don't do that, but, as the photo to the right from 2019 shows, they got buried in snow often enough that it isn't a problem.

In 2022, I "dirtscaped" my newer platforms, giving them more realistic "hills," plus real plants and miniature trees. This also changed where I would be placing buildings, and even which buildings I used.

For our August and November open RRs, we left our model buildings in place, but I ran wiring to light several that hadn't been lit before.

For buildings that didn't have lighting before I soldered several sockets that would hold typical garden lighting "wedge" bulbs to long stretches of wire. I made the wires long enough to reach all the way into my train shed, where the power supplies would be protected.

I also use 4-watt bulbs. Even those are too bright for some buildings but nobody seems to make 2- or 3-watt bulbs. Many systems today use 20-watt bulbs, which is great for lighting garden paths, but will give most buildings a radioactive glow.

Using "twist caps/terminals" like the ones shown on the left, I connected the wires to the power supplies. If two or three buildings were clustered together, I connected their wires together, hiding the junction under a building, and then ran a long wire to the power supply.

On my previous railroad, I had two levels and most of the buildings on each level were pretty close to each other. So Malibu-type power supplies with timers worked great - I just ran that black wire all over my railroad and buried it in mulch or gravel.

In addition, the light sockets I had then (from a now-abandoned electronics warehouse), had little tabs that allowed me to screw them into a permanent position in the little houses - so most of the structures you see are pre-wired, as it were, then connected to the Malibu system.

The building in the back, I admit, was lit by the "setting the building on top of the light" technique that folks like Marc Horowitz despise because light can leak around the base of the structure.

On this railroad, I only have two to four buildings in any cluster, and the clusters are spread out. For the power running to each little cluster, I am mostly using mostly 12-volt "wall warts" from defunct appliances. I try to buy 1-amp ones from second-hand shop. No, you're not supposed to use them outside. But these aren't outside, technically.

In fact I used one under a building on my old RR, and never had an issue with it. Not saying you should "try this at home."

I generally hook only 3-4 building lights up to each one to keep them from getting too warm. Though they are DC, the Malibu-style 4-watt incandescent wedge bulbs don't care which direction the electricity is coming. If you are using LED's, you will need to pay attention to polarity. BTW, I don't use 12-volt LED garden lights because a 12-volt 4-watt LED garden light is equivalent to a 20-watt incandescent bulb or more. Maybe 1-watt garden lights will become available at some point.

Inside the train shed, I have the wall warts plugged into a power strip that plugs into a timer. At the moment, I have a tangle of wires, since I added circuits a little at a time.

No photos, I'm afraid. I have a new power strip system I plan to set up this summer.

Not all of my "summer" (model) buildings are pre-wired, though. The photo to the right shows one of my old 12-volt plugs and 4-watt lamps that sat underneath a farmhouse before I put it away for the winter.

I was able to use it to illuminate the North States "farmhouse" bird feeder that took its place for the winter.

Needless to say, my supply of screw-on 12-volt wedge sockets has run out, and I haven't been able to find an exact replacement.

The picture to the right shows the sockets I ordered from Parts Express last spring. The flexible rubber is supposed to help keep water from getting to the wiring, but the trade-off is it may push the bulb slightly out of the socket unless you are very determined to keep it pushed in.

I ordered two sets, then I stripped the ends and soldered longer pieces of lamp cord to all of them. There is probably a better version of these somewhere, but at least they're available.

In times past, when I wanted to use a North States "large church" or "large barn" as a "summer" (model) building on my railroad, I popped off the ugly base and camouflaged the bottom edge of the building sides.

But we get bad windstorms here, especially in the winter and early spring. So for my "winter" setup, I leave the bases on the feeders and fill them with gravel.

That means that all I have to do to insert a light bulb is drill a hole big enough for the bulb to fit through, as shown to the right.

When running the wires back to the power supply, I try to leave enough extra length so that I can turn the side with the bulb in it away from the viewer. That way the plastic divider that is intended to channel the bird seed down into the tray keeps you from seeing the bulb directly.

If these buildings were sitting close to the viewer, folks might notice that there's nothing inside. But for the most part, our visitors' line of sight keeps them from seeing that.

Why do I have so many of these? In years past, I've set "kids railroads" up all over the property for our Christmas-themed open railroads, and I used the buildings to make them look more like actual "railroads."

BTW, Menards often puts one or two buildings at a time on sale for $10 or so off. So when a new style I think will look nice on my RR comes out, I wait for it to go on sale.

Do some of them look pretty silly?

Yes, but for $14 or so versus $90 for a comparable POLA or PIKO building that will actually deteriorate faster than the feeder, no matter how well you protect it? They're certainly good enough for winter displays or "children's railroads."

Years ago, I talked to North State's marketing department about making door heights, etc. proportionate for garden trains. They thought I was dumb, but a couple years ago, they introduced two UK-looking buildings that have appropriate door heights.

Yes, I waited until they were on sale, but a couple of them may find their way (sans bases, with paint and other doctoring) to my "summer" railroad.

The photo to the right shows the western edge of my railroad, with the buildings that wintered over there. I inserted it here so you can see how the same buildings look lit up in the dark further down.

You may notice that the little house at the top center is a CMS structure (now discontinued). I couldn't fit any of the North States feeders there without their bases, and without their bases, our winter windstorms quickly send them to the pond.

The CMS building seems to hold its own, so I left it there over the winter (It already had a very protective paint job of course).

The photo to the right shows the same part of the railroad after dark. You can see a few places where the gravel doesn't keep the light leaking through or whatever, but I hope you can imagine the after-dark beauty you could add to your own railroad with a few dollars' worth of supplies.

When these buildings come off and the summer buildings go back on, some of the socket/lamp setups will be superfluous because the building that replace them already have lights installed in the interior. But some of the other sockets will be repurposed for buildings I haven't wired yet.

Is it silly to like my railroad to look just as nice after dark as it does during the day?

Conclusion

So I'm hoping you get some useful ideas. If nothing else, I've demonstrated that building lighting doesn't have to be a "big deal." Try a couple at first, and see if you don't get hooked. :-)

Keep in Touch

If you're headed toward or past Springfield, Ohio, please let me know, and I'll see if we can work out a quick visit.

Finally, please let us know about your ongoing projects. Ask questions, send corrections, suggest article ideas, send photos, whatever you think will help you or your fellow railroaders. In the meantime, enjoy your trains, and especially enjoy any time you have with your family in the coming weeks,

Paul Race

FamilyGardenTrains.com

Return to Family Garden Trains' Home Page - The home page with links to all the other stuff, including design guidelines, construction techniques, structure tips, free graphics, and more.

Proceed to "Pondscaping, Part 1" - In addition to a lot of spring maintenance I didn't have the heart to report, I also attacked a growing problem - erosion around our pond liner that looked bad and allowed excess weed growth. While I was evaluating alternatives, a garden railroading friend offered me a pile of rocks. So installing a rock border around the pond seemed like the best path.

Click on the photo to see our status as of early July, 2022.

Return to "Preparing for 2021's Christmas Train Day." - In preparation for our annual Christmas-themed open railway, I ran lighting to some of our buildings, installed rope lighting on one section, and chose appropriate rolling stock. I also lit a bunch of our dwarf conifers and ran colored light strands that would brighten up our waterfall after dark.

Click on the photo to see our status as of early November, 2021.

Return to "Making a Large Scale Ghost Train" - In preparation for an October open railway, I repainted and relabeled decrepit Bachmann Big Hauler pieces to create a one-of-a-kind Halloween train. Materials included purple spray paint and vinyl lettering I created on my Cricut. I added "ghost" passengers made from cheap Asian seated figures painted with glow-in-the-dark paint.

Click on the photo to see our status as of mid-October, 2021.

Return to "Portal Installation on the New Boston and Donnels Creek." . We shimmed out the frames for the tunnel entrances to make them more vertical, installed I.S.L.E. portals we had painted previously, and stacked stones around them to camouflage the wooden parts. There's a bit more work to do, but its a big improvement over black holes at each end of the tunnel

Click on the picture to see our status as of early October, 2021.

Return to "Dirtscaping on the New Boston and Donnels Creek, Part 3" - Raising 'mini-mountains' near the new tunnels to make them seem more blended into the dirtscape. Lots of rocks moved, and more trees trimmed and planted. Also, we moved our towns into position in preparation for a club meeting at our home.

Click on the photo to see our status as of mid-August, 2021.

Return to "Tunnel Framing on the New Boston and Donnels Creek, Part 2" - Adding rocks, dirt, and plants to the new tunnel structures. Because I wanted to transplant dwarf and miniature trees to the new "mountains," I had to move a substantial amount of rocks and dirt. But I feel the result will be well worth it, once the groundcovers fill in.

Click on the photo to see our status as of late July, 2021.

Return to "Tunnel Framing on the New Boston and Donnels Creek, Part 1." We planned and built two wooden boxes that would become the framework for two short tunnels on our raised platform railroad. That effort was made a little more complicated by the fact it was a "retrofit." I hadn't planned for them at first, so getting them in place took some finangling.

Click on the picture to see our status as of mid-July, 2021.

Return to "New Right-of-Ways on the New Boston and Donnels Creek RR" - Adding a loop based on 10'-diameter curves. Includes cutting and installing 2x6 roadbed, bridging the waterfall, and cutting a third passage through the train shed, as well as installing roadbed for two smaller loops.

Click on the picture to see our status as of late March, 2021.

Return to "Creating a Railroad Timetable" - No train station would be complete without a timetable showing arrivals and departures (as well as expected arrivals and departures). We made one with a big piece of underlayment, framed it with scrap lumber, cut lettering for it with a craftcutter, and lined it with striping tape. This one is hinged to a shallow shelving unit that is holding the dvds we sometimes watch while working on projects in our workshop.

Click on the picture to see our status as of January, 2021.

Return to "Christmas Preparations and Operations 2020" - A series of families were going to visit during the holiday season (masked and distanced, of course), so we just had to do a little Christmas decorating, and get as many trains running as possible for the kids. This included laying temporary ROWs on the new platform and setting up two Lionel RTP trains for kids to run.

Return to "Garage to Train Station, Part 2" - continuing to fix up one end of my garage to resemble a Victorian train station interior. I used a digital projector to outline vintage coach details for my windowframes. Then I painted the backgrounds, attached the windowframes, and installed them on the wall. A repro Regulator clock and other details are added.

Click on the picture to see our status as of late December, 2020.

Return to "Garage to Train Station, Part 1" - fixing up one end of my garage to resemble a Victorian train station interior. The initial steps included demolition, patching the ceiling and walls, moving electrical outlets, adding wainscotting and baseboard, and planning for windowframes with painted backgrounds.

Click on the picture to see our status as of early December, 2020.

Return to "Westward Expansion, 2020, Part 3" - Thanks to a spate of unusually warm weather in early November, I was able to get the new platform finished, lined with vinyl, and bordered with trim boards to keep the dirt and gravel in place.

The next "permanent" improvements will wait for now. In the meantime, we will set out buildings and a temporary loop or to entertain visitors between now and Christmas.

Click on the picture to see our status as of mid-November, 2020.

Return to "Westward Expansion, 2020, Part 2" - We had to be careful leveling the last joists so the frame, decking, and right-of-way would be as level as possible. Fortunately we were able to get enough lumber to get a good start on the frame.

We also added one last tweak to the frame design to make it easier to extend this platform to its originally planned size, if and when we get a chance to do so.

Return to "Westward Expansion, 2020, Part 1" - With a lumber shortage and warm weather running out, we revised our plans for the next addition, bought what decent lumber we could find, dug holes, installed posts, and attached joists.

We were hoping to get the lumber we need to finish the platform before cold weather set in. Click on the link to see our status as of late September, 2020.

Return to "Train Storage Solutions, 2020" - Using periods of cold weather to get things sorted in the garage, including shelf building and tips for schlepping trains from storage to the tracks.

Click on the following link to see our status as of late January, 2020. https://familygardentrains.com/newbost/20_1_19_shelves/shelves.htm

Return to "Expansion Planning, 2020" - Three years after starting a garden railroad in our new home, we are trying to figure out the best way to finish the last loop of our raised platform railroad. How to make room for 10'-diameter curves and more towns and industries, but still keeping things manageable requires some thinking and rethinking.

Click on the photo to see the options we were reviewing for the next and last expansion.

Return to "Winter Preparation, 2019" - After the big open railroad event, we try to prepare the railroad for the cold months, including populating the railroad with North States bird feeders so it doesn't look empty, adding an air pump and bubblers to the pond, and more.

Click on the following link to see our status as of early December, 2019. https://familygardentrains.com/newbost/19_11_24_winter_prep/19_11_24_winter_prep.htm

Return to "Christmas Train Day, 2019" - Three years after starting a garden railroad in our new home, we host another Christmas-themed open railroad, giving many families a jump start on Christmas celebrations and sharing the experience of running trains with lots of kids.

Click on the photo to see a brief record of our busiest weekend in November, 2019.

Return to "Preparing for Christmas Train Day 2019" - Wrapping up construction projects for 2019 and getting ready for our annual Christmas-themed open railroad. Includes new lighting and other features, providing a temporary home for a Hogwarts Express train, weather issues, and more. Click to go to article.

Click on the following link to see our progress of mid-November, 2019.

https://familygardentrains.com/newbost/19_11_01_prep_for_train_day/19_11_01_prep_for_train_day.htm

Return to Decking the NEW New Boston and Donnels Creek Part 2 - Getting the next part of the railroad ready to install trains. Includes installing 2"x6" decking, vinyl sheeting, edges to hold back the gravel, and corrugated steel panels. It's not done, but it will give us another place to set up trains for our next Christmas-themed open railroad.

Click on the photo to see our status as of late October, 2019.

Return to "Framing the NEW New Boston and Donnels Creek RR - Part 7" - Installing posts, joists, framing, and decking for the eastern expansion of the NEW New Boston and Donnels Creek. Although this installation was complicated by having to fit into an existing framework, the methods used could work for any raised-platform railroad.

Click on the following link to see our progress of early October, 2019.

https://familygardentrains.com/newbost/19_27_framing/19_27_framing_part_7.htm

Return to "Planning the NEW New Boston and Donnels Creek RR - Part 5" - Once the major components of the water feature were installed and tested, we decided to add one more bit of railroad proper before our "Christmas Train Day," this November. The addition, about 5'x11', will allow us to put a small train and some scenery closer to eye level for youngsters. Eventually it will be part of the larger plan that will allow us to run our bigger cars and locomotives.

Click on the photo to see our plans for the next addition, as of late September, 2019.

Return to Waterscaping Part 4. - Installing the last connecting pool, so the whole planned waterfall is complete except for dirtscaping and planting.

The process included checking the pump, extending the hoses, rescuing toads, building the platform, trimming the platform, testing the pool's location, etc.

Click the photo to go to the article.

Return to "Waterscaping, Part 3" - After seven months of crazy long work hours, I finally got some free time to continue working on the railroad. Weather permitting, I often worked all the live-long day. This article describes installing two posts that will eventually support the last connecting pool, then digging the big hole for the in-ground pond, complicated by a three-month drought that turned the ground to concrete.

Click on the photo to see our progress as of mid-September, 2019.

Return to Christmas Train Day, 2018 - After two years without our traditional Christmas Train Day (something we did from 2008 through 2015), we were anxious to get started again, even without a huge right of way to show off. The kids' trains, the extra Thomas railroad, the popcorn popper and two Bachmann Christmas trains got a big workout. And the visiting kids all loved it!

Click on the photo to see a lot of last-minute preparations and some photos of the November 10, 2018 event itself.

Return to "Adding a Train Shed Part 6" - Installing the board and batten siding on our train shed, installing the windows, installing the trim, testing the "tunnel entrances," and more.

By the way, going over lumber receipts in early 2019, I couldn't believe I was still siding the train shed in late October, and managed to have an open railroad in mid-November. It is a little crazy how fast things can go together if you have a deadline and a lot of gift cards.

Click on the photo to see our progress as of late October, 2018.

Return to "Adding a Train Shed Part 5" - Planning the doors, walls, and windows of our garden train shed.

Includes choosing the siding and windows, installing the door, painting the windowframes, and adding crosspieces to support the vertical siding boards.

Return to "Adding a Train Shed Part 4" - Choosing and installing underlayment and drip edge to protect the sheathing until I can get the final roof installed.

Now the roof is waterproof enough to get us through the next couple of months at least, maybe more.

Return to "Adding a Train Shed Part 3" - Adding fascia, sheathing, and end trim to the in-progress train shed.

I thought about bringing in helpers for this part, but a reader commented on how helpful it was to see how one person could do this sort of thing by himself, so I just kept plugging away.

Click on the photo to see our progress as of September 13, 2018

Return to "Waterscaping Part 2" - Getting this year's waterscaping project done (for now at least). Installing and dirtscaping the third level of the waterfall. Installing pump and filter, adding an extra container and modifying the ones we already had installed to keep the water running smoothly. And lots of other tweaking. Includes tips about introducing fish and plants, as well as other information about water features in general that you may find helpful.

Click on the photo to see our status as of August 5, 2018.

Return to "Adding a Train Shed Part 2" - Adding rafters to the frame of the in-progress train shed. Now it's starting to look like it might actually be a structure and not just a crazy collection of posts.

The way we got the rafters and ridge board up wouldn't work for everybody, but it worked for us, and hopefully will help other folks to "think outside the box" - literally in this case.

Click on the photo to see our progress as of July 14, 2018.

Return to "Adding a Train Shed Part 1" - What started out as a simple addition of a deck to stand on when putting trains on the track got a little more ambitious when I realized that JUST installing the deck this year would require more work next year. So we framed out what we planned to be a train shed attached to the railroad. If it ever gets finished, I can easily put trains on the track at a moment's notice instead of schlepping them out from the garage.

Click on the photo to see our status as of July 9, 2018.

Return to "Waterscaping the NEW New Boston and Donnels Creek Part 1," our article on getting the top two layers of the waterfall on solid footing and getting the third layer framed. After we finish decking and dirtscaping the third layer, we will probably add a washbasin or something for the water to flow into, then add a pump to get the waterfall flowing. No big pond until next year at least - too many other projects.

Click on the photo to see our progress as of June 13, 2018.

Return to "Dirtscaping the NEW New Boston and Donnels Creek RR, Part 2. - Adding barriers to keep the rocks, dirt, and plants where they're supposed to go, placing platforms and running wiring for buildings, adding rocks, dirt, and plants to the upper level of the railroad.

Click on the photo to see our status as of June 1, 2018.

Return to "Adding Raised Roadbed to the NEW New Boston and Donnels Creek, Part 2" - Trimming the corners off the roadbed on the upper layer and cutting the pieces that will support the curves on the middle layer. We need to get the upper two tiers of the pond installed before we totally complete this step, so the article doesn't quite show the finished product. You'll see it later as part of other articles.

Return to "Adding Raised Roadbed to the NEW New Boston and Donnels Creek RR, Part 1" - Sorting out our priorities for the spring and summer of 2018. There a lot of little chores we really should get done before we start on the next big addition. Click to see our plans as of February 27, 2018.

Click on the photo to see our status as of February 20, 2018

Return to "2018: Springing into Spring on the NEW New Boston & Donnels Creek RR." - Sorting out our priorities for the spring and summer of 2018. There a lot of little chores we really should get done before we start on the next big addition. Click to see our plans as of February 27, 2018.

Click on the photo to see our status as of February 20, 2018

Return to "Dirtscaping the NEW New Boston and Donnels Creek RR, Part 1. - Putting edging around the existing "layers" of the new railroad, and beginning to add gravel and rocks. There were a few test runs, but we got stopped early by bad weather before we could dump the rest of the rocks, gravel, and dirt, much less plant the plants we hoped to get in before snowfall.

Click on the photo to see our status as of November 21, 2017

Return to "Decking the NEW New Boston and Donnels Creek RR - Decking the 'middle layer' of our proposed three-tier outdoor railroad. Prepping more track, laying out track and decking to make certain we have measurements correct, installing most of the remaining decking for this layer.

Click on the photo to see our status as of October 25, 2017

Return to "Framing the NEW New Boston and Donnels Creek RR, Part 6" - Modifying and finishing the framing on the second layer, cantilevering, using R3 track versus all other pre-curved track formats, finalizing the track plan, why painting the track makes old and new track blend better, and more. This will be the last bit of "framing" in 2017, and it worked out well, considering.

Click on the photo to see our status as of October 15, 2017

Return to "Framing the NEW New Boston and Donnels Creek RR, Part 5" - Spreading the billboard-sourced vinyl underlayment on the top layer. Prepping used Aristo track for (hopefully) many more years of service. Laying the first loop of track, attaching power wires with spade terminals, and testing conductivity with a Bachmann streetcar.

Click on the photo to see our status as of October, 10, 2017

Return to "Framing the NEW New Boston and Donnels Creek RR, Part 4" - Planning and running the decking for the top layer, testing the track plan, checking clearances, prepping used track with new railjoiners, examining the vinyl I ordered to go over the decking, and more.

Click on the photo to see our status as of September 26, 2017

Return to "Framing the NEW New Boston and Donnels Creek RR, Part 3" - Getting the frame finished on the top layer, ordering other things I'd need eventually, deciding on materials for the decking on the top layer (at least).

Click on the photo to see our status as of September 17, 2017

Return to "Framing the NEW New Boston and Donnels Creek RR, Part 2" - Once I had the overall frame relatively solid, I hooked up the underground power lines to two GFI plugs that should be in easy reach once everything is finished. I also decided to frame out the top railroad layer while I could still access the center of the railroad easily. Because I was running out of vertical space, I reconfigured that layer. Then after I got the "core" pieces on, I changed my plan again. But the whole thing is getting easier and easier to visualize, and is getting closer to complete with every board I cut and fasten on.

Click on the photo to see our status as of September 7, 2017

Return to "Framing the NEW New Boston and Donnels Creek RR, Part 1" - Once I started dropping posts in the holes and screwing things together, I didn't want to stop before I had the basic frame built (for one thing, the wood warps less once it's fastened in place). Now the folks driving down the street past our house (we're on a corner lot) probably wonder if I'm building an elaborate chicken coop, but that's fine with me. I still need to make a few more lumber runs and do a lot more cutting and sawing, but having the basic frame in place should make the next bits a lot easier.

Click on the photo to see our status as of August 10, 2017

Return to "Breaking Ground on the NEW New Boston and Donnels Creek" - Okay, in case you wondered if we'd ever get started on the thing, we broke ground in July, using a manual post-hole digger. Well two manual post-hole diggers. But by the end of this article, we're ready for the posts to start going in.

Click on the photo to see our status as of the end of July, 2017

Return to "Planning the NEW New Boston and Donnels Creek, Part 4" - Well, the rented post-hole digger fell through, so we dug our vegetable garden with a manual post-hole digger (the scissors kind). In addition, I stake out where the railroad was going to be. Twice. And tweaked the plans again. Sorry about the redo's, but sometimes just walking around the yard trying to visualize things makes me reconsider something that seemed "settled" only a few days before.

Click on the photo to see what we were considering as of late May, 2017

Return to "Planning the NEW New Boston and Donnels Creek, Part 3" - We have still not broken ground. In part because we plan to rent a post-hole digger and dig the post holes for our raised vegetable garden and the first phase of the garden railroad at the same time, and we don't have enough lumber on hand yet. (If we didn't break it down into multiple trips, we'd be blowing out the shocks on our minivan.) In the meantime, we used a line level to see if the slope of the back yard was as bad as we thought it was (it's worse), and we did other site preparation, including planting a whole bunch of spruce tree seedlings to eventually give us some privacy in our side and back yard. Plus, I'm still wavering a little on the "where-to-start-first" issue.

Click on the photo to see what we were considering as of late April, 2017

Return to "Planning the NEW New Boston and Donnels Creek, Part 2" - More plans. We've moved on from the 2"x6" roadbed-on-posts to a sort of "train-table-outside" plan. Our goals include low-maintenance, high interest, and high reliability. We're also trying to get around having a thousand dollars' worth of dirt hauled into the back yard. If you want to get some idea of what our planning process looks like, reading these through in sequence may help. Or it may drive you crazy.

Click on the photo to see what we were considering in early April, 2017

Return to "Planning the NEW New Boston and Donnels Creek, Part 1" - If you're subscribed to our newsletter, you know that we moved just after Thanksgiving in 2016, leaving behind most of the track, a few of the bird feeders, and one Bachmann train set for the new owners. We also left behind a high-maintenance garden that we do not intend to replicate at the new place. This is the first chapter of a new chapter in our lives, which we hope will include a lot of "lessons learned." But first, some serious landscaping had to take place.

Click on the photo to see what we were considering in March, 2017

Return to the New Boston and Donnels Creek RR Page - This is the page describing Paul Race's progress and frequent rework on his own garden railroad, started on a shoe-string budget in 1998, later expanded, and later refurbished several times as issues arose. Issues that Paul hopes to avoid by building the next iteration above ground.

Click on the photo to see the home page of Paul's railroad.

Return to Family Garden Trains' Home Page - The home page with links to all the other stuff, including design guidelines, construction techniques, structure tips, free graphics, and more.

To read more, or to look at recommended Garden Railroading and Big Indoor Train products, please click on the index pages below.